IEC Dimensions of Mechanical Structures of the mm (19 in) Series Part 1: Panels and Racks. IEC Mechanical structures for electronic equipment – Dimensions of mechanical structures of the ,6 mm (19 in) series – Part Basic. IEC Dimensions of Mechanical Structures of the mm (19 Inch) Series Part 2: Cabinets and Pitches of Rack Structures.
|Published (Last):||12 April 2012|
|PDF File Size:||2.60 Mb|
|ePub File Size:||8.27 Mb|
|Price:||Free* [*Free Regsitration Required]|
Two-post racks provide two vertical posts. This page was last edited on 12 Decemberat These cases can be isolated by thick layers of foam or may use spring-loaded shock mounting. The size denotes the width of the faceplate for the installed equipment. Equipment can be mounted either close to its center of gravity to minimize load on its front panelor via the equipment’s front panel holes.
The gap between the posts is millimetres Examples include telephone exchanges, network cabling panels, broadcast studios and some government and military applications. The strength required of the mounting posts means they are invariably not merely flat strips but actually a ifc folded strip arranged around the corner of the rack.
Computer servers designed for rack-mounting can include a number of extra features to make the server easy to use in the rack:.
IEC | IEC Webstore
However, not all equipment is suitable for this type of mounting. These cases are marketed to musicians and entertainers for equipment not subject to frequent transportation and rough handling. Racks are divided into iwc, The term relay rack appeared first in the world of telephony.
A rails kit may include a cable management arm or CMAwhich folds the cables attached to the server and allows them to expand neatly when the server is slid out, without being disconnected.
However, some rack equipment has been designed to make fan replacement easy, using quick-change fan trays that can be accessed without removing the cabling or the device from the rack, and in some cases without turning off the device so that operation is uninterrupted during replacement.
inch rack – Wikipedia
The earliest repeaters from were installed in ad-hoc fashion on shelves, in wooden boxes and cabinets. Each module has a front panel that is 19 inches Square-hole racks allow 6297 mounting, such that the rack-mount equipment only needs to insert through and hook down into the lip of the 602297 hole.
The First Stored Program Computer. There are a multitude of specialty server racks including soundproof server racks, air conditioned server racks, NEMA rated, seismic rated, open frame, narrow, and even miniature inch racks for smaller applications.
When in place, the equipment may also then be bolted to the rack. Patent 2,granted Oct. In contrast to the “inch world”, ETSI also defined the size of the rack enclosure: The cases typically use extruded aluminum bands at the ends of the body with 6029 mating to like bands for the covers.
In the case of network equipment, it may be necessary to unplug 50 or more cables from the device, remove the device from the rack, and then disassemble the device chassis to replace the fans. The rack unit is a measure of vertical spacing and is common to both the 19 and 23 inch racks. The posts have holes in them at regular intervals, with both posts matching, so that each hole is part of a horizontal pair with a center-to-center distance of Hole spacing is 25 millimetres 0.
Equipment designed to be placed in a rack is typically described as rack-mountrack-mount instrumenta rack mounted systema rack mount chassissubrackrack mountableor occasionally simply shelf. Computer enclosure Mechanical standards Server hardware. This is usually required by local building codes in seismic zones.
Patent 3,granted June 4, Iev to Telcordia Technologies Generic Requirements document GRCORE, during an earthquake, telecommunications equipment is subjected to motions that can over-stress equipment framework, circuit boards, and connectors. With the prevalence of inch racks in the Telecoms industry, the same practice is also common, but with equipment having inch and inch brackets available, enabling them to be mounted in existing racks.
The inch rack format has remained constant while the technology that is mounted within it has changed considerably and the set of fields to isc racks are applied has greatly expanded. A third common use for rack-mounted equipment is industrial power, control, and automation hardware. This prevents circular airflows where hot exhaust air is recirculated through an adjacent device and causes overheating.
They allow for dense hardware configurations without occupying excessive floorspace or requiring shelving. The inch dimension includes the edges, or “ears”, that protrude on each side which allow the module to be fastened to the rack frame with screws. In the event of a nut being stripped out or a bolt breaking, the nut can be easily removed and replaced with a new one. Road case racks come in different heights based on the 1U standard and different depths.
Common uses include server, telecom, broadcast video, lighting, audio, and scientific lab equipment.
Larger cases are further reinforced with additional plywood or sheet metal. Production of clearance-hole racks is less expensive because tapping iecc holes is eliminated and replaced with fewer, less expensive, cage nuts. This of course varies by manufacturer, the design of the rack and its purpose, but through common constraining factors such as raised floor tile dimensionsthese dimensions have become quite common.